:O

:confused Why would you want a I4 in a heavy tiller?

:megaphone V-TWIN RUMBLE BABY :hail

 

Sticking feathers up your butt doesn't make you a chicken...

Get a GSXR 750 or 600 and toss the 1K motor in there.

Why would you want to put the I4 1K motor in a v-twin frame?:confused

 

uke I can't believe what i reading uke

Im thinkin :thatsgay

 

I don't think it is even possible. The I4's sit transversely, making the bikes very wide. The twins are usually pretty narrow, so I doubt it would fit.

If you really want a gixxer motor, get a gixxer, it would be easier, cheaper, and make a better bike than the hybrid.

 

:thatsgay Not only will it not fit, but it is a pain in the a$$ to even put a 750 motor in a 600 frame.



Don't ask how I know this.:devious

 

Sticking feathers up your butt doesn't make you a chicken...

It might make you :thatsgay though.

 

if you like the look of the tiller just get gixxer 1k and modify the tiller plastic to fit the gixxer.

 

:confused :hmm :dunno

 

Nope, not happening ... but do us a favour and ask the question on gixer.com, the results should be hilarious

Hey tiller1000, the SRAD GSXRs aren't too bad to swap if you are prepared, my mate JV did it several times during the TT a couple of years ago, to race in more classes...

 

Hmm, what about a TLR engine in a GSXR chassis? :devious

All you'd need is a 20-ton press to squeeze the spars closer together and you're done! Right? It's like lego isn't it? :coocoo

 

I am wondering what this has to do with comments and suggestions?
:rant

 

:O Close this thread and send it to Gixxer.com or any other non
TL site :rant

And why not put 4 TL motors in a viper instead :confused

 

fishing for trolls? :dunno

 

Damn you guys are ruthless :laugh

 

Hmm, what about a TLR engine in a GSXR chassis? :devious

All you'd need is a 20-ton press to squeeze the spars closer together and you're done! Right? It's like lego isn't it? :coocoo

Hmmm, how about side by side TL motors in a Gixxer frame. 250HP V4!

Oops, that was out loud wasn't it?

 

:rant I4 in a TLR!:coocoo :kicknuts
Next thing will be a LT1 in a TLR!:cuckoo :yeahright

 

i like the look of a tiller can it be done or not?

 

i like the look of a tiller can it be done or not?

Anything can be done with enough time, money and jury-rigging. If you're asking whether or not anyone here has done it the answer is no.

 

It would be easier to fit tiller plastic to a gixxer, but then it is just a fake with an i4:thatsgay

 

:thatsgay

 

hey, maybe the guy just has an I4 1000 sitting around, and wanted to know if it would fit in a TLR.....you guys are harsh

but I would think that it is not possible.

go with fitting TLR plastics on a gixxer...you could probably get Hammerit to make some plastics for you...but it will most likely cost quite a bit

 

Pipoloco------> :kicknuts <------- Common sense

THere now think about what you are doing

 

sniff sniff.........













I SMELL SQUID!!Pipoloco----> :bash <----ME

Common bro, you just knew you were gonna take an ass beating for this!:laugh

 

Well the idea isent all that bad :O
But I would rather fit a TLR engine in a gixxer frame :hail

 

i have in my tiller a problem when i do wheelies iol leaks thru the back of the engine rigth by the front sproket does someone have an idea of what could be,?

thank you.